For Research Use Only. Not for use in Diagnostic Procedures. Trademarks and/or registered trademarks mentioned herein are the property of AB Sciex Pte. Ltd., or their respective owners, in the United States and/or certain other countries. For information on availability, please contact your local representative.
AB SCIEX™ is being used under license. Beckman Coulter® is being used under license. ICAT™ is a trademark of the University of Washington and is exclusively licensed to AB Sciex Pte. Ltd.
© 2019 DH Tech. Dev. Pte. Ltd.

Knowledge Base Articles

Knowledge Base is your tool to finding answers about common questions. Browse all Knowledge Base articles below.

View:
All Articles My Articles Premium Access
Filter Results

Filter Results

Capillary Electrophoresis Instruments

HPLC Products

Ion Mobility Spectrometry

Mass Spectrometers

Software

Standards and Reagents

MultiQuant Software

Absence of Calibration Curve in Analyst® or MultiQuant™ Software Due to Omitted Standard Concentration Values

If actual concentration values for standards are omitted from a MultiQuant™ or Analyst® software results table, then the data points for standard concentration versus peak area will all be aligned with zero on the x-axis in the calibration curve, looking nothing like the expected diagonal line. Adding the actual concentration information for the standards spreads the points across the x-axis and restores the expected diagonal linear regression line.

10/17/2019    Analyst Software | MultiQuant Software

What File Format Can Report Templates Be Created In?

Report templates—used to create reports from results tables generated in Sciex OS, MultiQuant™ and Analyst® software—must always be in the format of a Word document with a file extension .docx. However, the output report itself can be created in several formats including Word, HTML, PDF, and CSV.

10/16/2019    Analyst Software | MultiQuant Software | SCIEX OS Software

Data for Custom Calculations Show as Not Calculated on a Report

In reports created from results tables in Analyst® and MultiQuant™ software, queries are used to compute the values for custom calculations, but occasionally the data appears as "Not calculated" on the report. This issue appears when the query file linked to the report template is not saved to the same folder as the report template.

10/11/2019    Analyst Software | MultiQuant Software | SCIEX OS Software

To Make Reporter Tags Visible in a Report Template Unblock Them

If a report template is emailed or transferred to another computer and then opened, the xml tags may not be visible because they were blocked for security reasons.

10/10/2019    Analyst Software | MultiQuant Software | SCIEX OS Software

Can Standard Concentration Values Be Stored in a MultiQuant™ Software Quantitation Method?

No, the concentration values for a standard or quality control samples cannot be stored in or saved to the MultiQuant™ software quantitation method.

10/9/2019    MultiQuant Software

Resolving the PeakView™ 2.2 and MultiQuant™ 3.0.3 Software Error after Upgrading to .NET 4.7.2

After upgrading PeakView™ software to version 2.2 or MultiQuant™ software to version 3.0.3, the following error message was generated: "The procedure entry point nextafterf could not be located in the dynamic link library MSVCR120_CLR0400.dll." The workaround is to remove .NET Framework 4.7.2 and then install the .NET 4.0 software.

9/26/2019    MultiQuant Software | PeakView Software

Can the Default Location of MultiQuant™ Software Queries Be Changed?

It is not possible to change the default location of MultiQuant™ software queries.

9/16/2019    MultiQuant Software

Converting MultiQuant™ Software Qmethods to Sciex OS Software Qmethods

This article contains a step-by-step guide for converting a MultiQuant™ 3.0.3 software quantitation method (.qmethod) file to a Sciex OS 1.5 software quantitation method file (.qmethod).

6/26/2019    MultiQuant Software | SCIEX OS Software

Compatibility of Standard MutliQuant™ Software Files with MultiQuant MD Software

This article describes the compatibility of standard, non-GLP MutliQuant™ software files with MultiQuant MD software.

12/28/2018    MultiQuant Software

Changing the Orienatation of Peak Review Chromatograms in a Reporter Template

If the peak review chromatograms are showing in the wrong orientation on an Analyst® or MultiQuant™software report, the page orientation for the actual Word document template may be set to portrait rather than landscape.

12/28/2018    Analyst Software | MultiQuant Software | SCIEX OS Software
We use cookies and by using this site or closing this message, you agree to our privacy policy.
Accept Cookies
×

For Research Use Only. Not for use in Diagnostic Procedures. Trademarks and/or registered trademarks mentioned herein are the property of AB Sciex Pte. Ltd., or their respective owners, in the United States and/or certain other countries. For information on availability, please contact your local representative.
AB SCIEX™ is being used under license. Beckman Coulter® is being used under license. ICAT™ is a trademark of the University of Washington and is exclusively licensed to AB Sciex Pte. Ltd.
© 2019 DH Tech. Dev. Pte. Ltd.